About 1,800,105 results (4,226 milliseconds)
Family Fun: Soda Pop Bottle Launcher - Mom it ForwardMom it ...
http://feedproxy.google.com/~r/MomsWhoBlog/~3/a5bnIpIZMBc/family-fun-soda-pop-bottle-launcher Jul 6, 2019 ... 2 inch long x 1 1/2" diameter PVC Pipe; 2 pieces of 8 foot x 1/4 ... Put Duct Tape as needed inside the 2" PVC Pipe on one side. This ...
Burying coaxial cable
https://groups.google.com/g/rec.radio.amateur.antenna/c/qcarKV0-POw >>I would like a bit of input on burying coax in PVC pipe. I have not done ... 1/2 inch larger pipe...never hurts to have lots of room as pulling and ...
kites4all - Hot Tools
https://sites.google.com/site/kites4all/home/hot-tools The white tool holders are 1" Schedule 40 PVC pipe (thin ... The pieces of PVC are screwed to blocks of one inch pine that are 2-1/2" wide and 2" tall.
CX500Gl500 - Fork Preload Spacers
https://sites.google.com/site/cx500gl500/fork-preload-spacers ... 1/2 inch pvc pipe coupler. They cost about 29 cents and fit right where they need to. In addition to adding spacers it is also a good idea to drain the fork ...
Mattatuck Madness Maple Syrup - 4" x 40" RO Build
https://sites.google.com/view/mattatuckmadnessmaplesyrup/4-x-40-ro-build ... , Plastic Pipe Cutter, PEX Pipe Cutter, PVC Cutter Tool, PVC Ratchet Cutter $10. Milrose 70885 Blue Monster 1/2 Inch x 1429 Inch Blue Teflon Tape (3 Pack) $15.
Drill a hole in concrete block wall for a 1/2" PVC pipe
https://groups.google.com/g/alt.home.repair/c/cYmaTfMf-gg ... make two trips there to rent and return. Well as expected, whenever ... Drilled one hole and the stupid drill ran out of battery after one minute. They did ...
SWR on vertical goes out of whack... why?
https://groups.google.com/g/rec.radio.amateur.antenna/c/_yOsHcyfM7E > it's electrically insulated via a 1/2" PVC pipe with a 1/2" PVC union > to ... They would intermit as one section would lose connection. Sometimes I ...
3/4 or 1" PEX??
https://groups.google.com/g/alt.home.repair/c/tDrY3w0xWhg If it was all done with 1/2 inch copper pipe the way some cheap houses are built now, tenants would be fighting over water pressure. The obvious advantage ...
Ladder Line Entry to Shack
https://groups.google.com/g/rec.radio.amateur.antenna/c/H4yXyvwkaNk Another possibility is to put two 1/2 inch pvc pipes inside your 4 inch pipe, split the ladder line down the middle and run each wire through a 1/2 pipe.
Homebrew Coil Form Factor
https://groups.google.com/g/rec.radio.amateur.antenna/c/6s_Gm_9ASjU form with plastic dowel glued on each corner of the wood. I could also make a similar coil using PVC pipe. ... Wound the wire around a piece of 1/2 inch PVC pipe ...
Mattatuck Madness Maple Syrup - Cleaning and Storing RO ...
https://sites.google.com/view/mattatuckmadnessmaplesyrup/cleaning-and-storing-ro-membranes Storing your membranes in the off season: The easiest way to do this is to make PVC vessels. 3” PVC pipe works well - I made 2 - 40" canisters because they are ...
How to avoid ice-clogged furnace air intake pipe?
https://groups.google.com/g/misc.consumers.house/c/yVxRABx-2VA By the way, I double-checked. 1) They really do face east (intake) and west (exhaust). ... I solved my problem by installing a 2 inch to 4 inch pvc pipe ...
Real World Audio - Comments worth Answering
https://sites.google.com/view/realworldaudio/from-the-yt-channel/comments-worth-answering On a budget I would go 1/2 inch Baltic Birch and if you want to go further ... Perhaps they are making more money with other products. The FE103NV2 has ...
Moges´s Class room - How to make Peterson Press
https://sites.google.com/site/ethiograd123/word-of-the-week/untitledpost Jun 14, 2011 ... 2. Two 20x5cm lumber cut in rectangle. 3. One 11cm PVC pipe, 80 gauge (thick one) 30cm long. 4. One 2-2(1/2 )inch steel pipe 30cm long. 5. Four ...
A few questions about collinear coaxial antennas
https://groups.google.com/g/rec.radio.amateur.antenna/c/DREJnRznluQ down a pipe. >I bought 1-1/2 inch rubber washers with a 3/16 hole in the >center that will slide over the coax and then be pulled into the 1-1/4 inch >PVC ...
Homemade DIY Weather Instruments
https://sites.google.com/site/weathermake2000/ (13) Six inch section of 1/2 inch aluminum pipe or sturdy plastic to make the windvane ... (PVC pipe fitting). The top of the cover was cut from a 1/2 inch ...
Source for reverse-threaded (non-bulkhead) PVC fittings for ...
https://groups.google.com/g/alt.building.construction/c/KtnaVkLClnw Jan 31, 2009 ... fittings (1/2", 3/4", and 1" size)? I'm adapting a PVC greenhouse design, and would need to be able to rotate a series of PVC pipes that cross ...
[IW5EDI] A 50 Ohm Dummy Load
https://groups.google.com/g/rec.radio.amateur.antenna/c/znso6AITn20 They are made from 1/2 PVC pipe and # 10 wire (stripped from Romex) for ... Spacing between elements are 34 and 1/2 inches. The elements are 1/2 inch ...
Fusor High Voltage Power Supply thread
https://groups.google.com/g/heatsynclabs/c/rlzMKPioyDA I am estimating around 2 1/2 inches in diameter if rolled very tight and with no inner core to make winding easier. If we start with a 1/2 PVC pipe, the ...
Aluminum tubing for vertical antenna
https://groups.google.com/g/rec.radio.amateur.antenna/c/1rt1N_vz9qA must be something they do with you on the phone? I'll call 'em Monday ... chain link fence line pole (about 1-1/2 inch diameter, steel), driven 4 feet ...